Accurate Air Flow Calculator
Calculate CFM, duct velocity, air changes per hour, heat load, and friction loss - with round, rectangular, and oval duct support in both metric and imperial units.
How to Use This Calculator
- Pick your unit system. Imperial (CFM, FPM, inches) for US HVAC work. Metric (m3/h, m/s, mm) for everywhere else.
- Choose your tab. Duct Velocity for airflow from velocity and duct size. Air Changes for required CFM from room volume and ACH target. Heat Load for CFM from BTU and temperature difference. Converter for quick unit conversions.
- Select duct shape. Round, rectangular, or oval. The calculator computes cross-sectional area automatically.
- Enter your figures. Use realistic velocity and ACH values - the hints and reference tables below show typical ranges.
- Click Calculate Air Flow. You get primary result, all unit conversions, friction loss estimate, and practical guidance.
What Makes This Different
Most air flow calculators handle one equation or one duct shape. This one covers the four calculations HVAC technicians and engineers actually need, with context most tools skip:
- Four calculators in one. Duct velocity, air changes per hour, heat load, and unit converter - no need to switch tools.
- Round, rectangular, and oval ducts. Automatic cross-sectional area calculation for all three shapes. Oval uses the flat-oval standard equivalent.
- Friction loss estimate. Enter duct length and get pressure drop per 100 ft and total pressure loss using ASHRAE-based friction equations.
- All units shown at once. CFM, m3/h, L/s, FPM, m/s - every conversion visible in the same result card.
- Real-world ACH targets. Preset dropdown for storage, home, kitchen, commercial kitchen, and cleanroom - with custom option.
- Fan power estimate. See the approximate watts required to move the air, so you understand the energy cost.
- Practical guidance. Velocity warnings, recommended ranges, and duct sizing tips tied to your result.
- Transparent formulas. Every equation documented with its source and assumptions.
How the Calculation Works
Air flow calculation reduces to a small set of identities. Everything else is a rearrangement:
Step-by-Step Logic
| Step | What happens |
|---|---|
| 1 | Duct dimensions are converted to a cross-sectional area in square feet (imperial) or square metres (metric). |
| 2 | Air flow equals velocity x area. Round ducts use pi x r squared. Rectangular use W x H. Oval uses the standard flat-oval equivalent. |
| 3 | Flow is converted to all common units: CFM, m3/h, L/s, m3/min. |
| 4 | ACH is calculated from CFM and room volume. Or, in reverse, required CFM is calculated from room volume and target ACH. |
| 5 | Heat load CFM uses the sensible heat equation with the 1.08 constant (for standard air at sea level). |
| 6 | Friction loss is estimated using the ASHRAE-based equation, giving inches of water per 100 ft of duct. |
| 7 | Fan power is estimated from flow and total pressure using the fan power equation. |
Duct Area Formulas
| Shape | Area Formula | Example |
|---|---|---|
| Round | A = pi x (D/2)^2 | 8 in duct = 0.349 ft2 |
| Rectangular | A = W x H | 12 x 8 in = 96 in2 = 0.667 ft2 |
| Oval (flat-oval) | A = (W - H) x H + pi x (H/2)^2 | 12 x 6 in oval = 0.481 ft2 |
Reference Tables
Typical Air Velocity by Application
| Application | Velocity (FPM) | Velocity (m/s) |
|---|---|---|
| Residential main trunk | 600 - 900 | 3.0 - 4.6 |
| Residential branch | 400 - 600 | 2.0 - 3.0 |
| Commercial main trunk | 1000 - 1500 | 5.1 - 7.6 |
| Commercial branch | 600 - 1000 | 3.0 - 5.1 |
| High-velocity industrial | 2000 - 2500 | 10.2 - 12.7 |
| Dust collection transport | 3500 - 4500 | 17.8 - 22.9 |
Recommended ACH by Space Type
| Space | ACH Range | Purpose |
|---|---|---|
| Storage / garage | 1 - 2 | Minimal ventilation, odour control |
| Standard home / office | 3 - 5 | Comfort, humidity, CO2 control |
| Kitchen / bathroom | 5 - 8 | Moisture, odour, grease removal |
| Commercial kitchen | 8 - 15 | Heat, smoke, grease extraction |
| Laboratory | 10 - 15 | Fume control, safety |
| Hospital / cleanroom | 15 - 25 | Infection control, particulate removal |
Air Flow Unit Conversions
| From | To | Multiply By |
|---|---|---|
| CFM | m3/h | 1.699 |
| CFM | L/s | 0.4719 |
| m3/h | CFM | 0.5886 |
| m3/h | L/s | 0.2778 |
| FPM | m/s | 0.00508 |
| m/s | FPM | 196.85 |
| in.wg | Pa | 249.09 |
| Pa | in.wg | 0.004015 |
Worked Examples
Example 1 - Duct velocity method (8-inch round, 800 FPM)
| Step | Value |
|---|---|
| Duct diameter | 8 in = 0.667 ft |
| Cross-sectional area | pi x (0.333)^2 = 0.349 ft2 |
| Velocity | 800 FPM |
| Air flow | 0.349 x 800 = 279 CFM |
| In metric | 279 CFM = 474 m3/h = 132 L/s |
| Friction loss (50 ft duct) | 0.24 in.wg per 100 ft, 0.12 in.wg total |
Example 2 - Room ACH method (20 x 15 x 9 ft room, target 4 ACH)
| Step | Value |
|---|---|
| Room volume | 20 x 15 x 9 = 2,700 ft3 |
| Target ACH | 4 |
| Required air flow | (2,700 x 4) / 60 = 180 CFM |
| In metric | 180 CFM = 306 m3/h |
| Recommended duct size | 8-inch round at about 660 FPM, or 10 x 6 rectangular |
Example 3 - Heat load method (24,000 BTU/hr, 20 degree delta)
| Step | Value |
|---|---|
| Sensible heat load | 24,000 BTU/hr |
| Temperature difference | 20 degrees F |
| Required air flow | 24,000 / (1.08 x 20) = 1,111 CFM |
| In metric | 1,111 CFM = 1,888 m3/h |
| This is a 2-ton system | Typical 2-ton AC needs 800-1,200 CFM |
Example 4 - Rectangular duct (12 x 8 inches, 1,000 FPM)
| Step | Value |
|---|---|
| Width x Height | 12 x 8 in = 96 in2 |
| Area in ft2 | 96 / 144 = 0.667 ft2 |
| Velocity | 1,000 FPM |
| Air flow | 0.667 x 1,000 = 667 CFM |
| In metric | 667 CFM = 1,133 m3/h |
| Equivalent round | About 11-inch round duct |
Practical Tips
- Use the right velocity for the job. Residential trunk lines run 600-900 FPM. Branch runs 400-600. Commercial systems run higher. Dust collection needs 3,500+ FPM to keep particles suspended.
- Check ACH for ventilation. Homes and offices need 3-5 ACH for comfort. Kitchens and bathrooms need 5-8. Commercial kitchens and labs need 8-15. Cleanrooms need 15-25.
- Match duct size to airflow, not the other way around. Use the ACH method to find required CFM, then size the duct for the correct velocity.
- Friction loss compounds. Every 100 ft of duct adds pressure drop. Long runs, elbows, and transitions add more. Keep total static pressure within the fan's rating.
- Altitude matters. The 1.08 constant in the heat load equation assumes sea-level air density. At 5,000 ft, use 1.00. At 8,000 ft, use 0.95.
- Velocity too high means noise. Above 1,200 FPM in residential systems, you will hear whistling at grilles and dampers. Above 2,000 FPM, noise becomes objectionable in most spaces.
- Velocity too low means poor distribution. Below 300 FPM, air may stratify and not reach the occupied zone. Below 200 FPM in horizontal runs, dust can settle.
- Always verify with a balometer. Calculations give you the target. A flow hood or balometer at the grille confirms what is actually happening.
Frequently Asked Questions
CFM (cubic feet per minute) measures volumetric air flow - how much air moves. FPM (feet per minute) measures velocity - how fast it moves. They are related by duct area: CFM equals FPM times area. A large duct can carry the same CFM as a small duct at lower velocity.
Use the sensible heat equation: CFM equals BTU/hr divided by (1.08 times temperature difference in F). The 1.08 constant applies at sea level. At altitude, substitute 1.00 for 5,000 ft or 0.95 for 8,000 ft.
Residential main trunks: 600-900 FPM. Residential branches: 400-600 FPM. Commercial mains: 1,000-1,500 FPM. Below 300 FPM risks poor distribution; above 1,200 FPM in residential causes noise.
Standard living spaces need 3-5 ACH. Kitchens and bathrooms need 5-8. Commercial kitchens and labs need 8-15. Cleanrooms and hospitals need 15-25. Garages and storage can run 1-2.
Round ducts have the lowest friction for a given cross-sectional area and are preferred where space allows. Rectangular ducts fit in tight spaces like wall cavities and above ceilings. Oval (flat-oval) ducts are a compromise - they fit in shallow spaces but have higher friction than round.
Multiply CFM by 1.699 to get m3/h. Multiply m3/h by 0.5886 to get CFM. The Converter tab handles this automatically for flow, velocity, dimensions, and pressure.
Friction loss is the pressure drop as air moves through ductwork. Every foot of duct, every elbow, and every transition adds resistance. If total friction loss exceeds the fan's static pressure rating, airflow drops. This calculator estimates friction loss per 100 ft using ASHRAE-based equations.
Yes. Air density decreases with altitude, so the same fan moves less mass of air at higher elevations. The heat load equation uses a 1.08 constant at sea level. At 5,000 ft, use 1.00. At 8,000 ft, use 0.95. Velocity-based calculations are less affected because they measure volume, not mass.
It depends on target velocity. At 800 FPM, you need 1.25 ft2 of area - a 12-inch round duct (0.785 ft2) would run at about 1,274 FPM, too high for residential. Use a 14-inch round (1.07 ft2) for about 935 FPM, or a 16-inch round (1.40 ft2) for about 714 FPM. The Duct Velocity tab calculates this for you.
References & Methodology
- ASHRAE Handbook - Fundamentals. Duct Design. American Society of Heating, Refrigerating and Air-Conditioning Engineers, current edition.
- ASHRAE Standard 62.1. Ventilation for Acceptable Indoor Air Quality. American Society of Heating, Refrigerating and Air-Conditioning Engineers.
- SMACNA. HVAC Duct Construction Standards - Metal and Flexible. Sheet Metal and Air Conditioning Contractors' National Association.
- BAPI. Determining Duct Air Flow in CFM using the BAPI Pressure Sensor. Application Note, 2015.
- TSI Incorporated. Flow Rate Calculations. TSI Application Note.
- Engineering Toolbox. Duct Velocity. engineeringtoolbox.com, 2005.
- ACCAdemic. Airflow and CFM Air Exchange Calculator. protoolreviews.com, 2026.
- Angi. How to Calculate CFM. angi.com, 2025.
- NY Engineers. What Is CFM in HVAC and How to Calculate It. ny-engineers.com, 2025.